Quiz Buzzer Set - Geopardy8!

by hausofpayne17 in Circuits > Arduino

77 Views, 0 Favorites, 0 Comments

Quiz Buzzer Set - Geopardy8!

This is an Arduino Nano-based basic "lock-out" quiz buzzer set for 8 players (two teams of 4). You can make it smaller if you prefer.

Retail products cost hundreds of dollars. This project can be built for about $25 in parts (based on AliExpress prices)

This is a great project for middle/high school Computer Science or Engineering students. I've had my students build this kind of game circuit in the past.

When a player buzzes in, the other players are locked out. The quizmaster then presses the 'Clear' button if the given answer is wrong or the 'Score' button for a correct response. In the latter case, 10 points are added to the team's score and the scores are redisplayed on screen

This project displays the game score in the Serial Monitor. At the end of this Instructable, there is a reference to how to use the Processing language to build a Graphical Interface when the program receives codes from the Arduino.

You'll likely want to make individual buzzers on cables that reach across the tournament table. (It's impossible for 8 people to crowd around this breadboard :-)

This Instructable assumes you are familiar with the basics of Arduino circuit construction and programming.

(If you want an Introductory Arduino course, go to my document here.


Let's get Building!

Supplies

  1. Arduino Nano (clones are fine) - For 8 players, digital pins 2 to 13 and analog pins A0 to A6 are needed to accommodate the buttons, lights and quizmaster buttons. A standard Arduino UNO does not have enough analog pins for 8 players but if you're building for fewer players, an UNO is fine.
  2. eight(8) LEDs (4 of the same colour for each team if you like)
  3. eight(8) 470 Ohm resistors (current limiting for the LEDs)
  4. nine(9) 10K Ohm resistors (pull down resistors for the player buttons and 'Cancel' button)
  5. one 1K Ohm resistor (for the ANALOG pin A6 'Score' button)
  6. 10 momentary contact buttons
  7. 1 Small 8 Ohm speaker (~30mm) OR Piezo buzzer and a 100 Ohm resistor (to reduce the annoying loudness a bit). THE SPEAKER SOUNDS MUCH NICER!
  8. 1 Standard size breadboard (make sure the rails connect the WHOLE breadboard top and bottom. If not, use little jumper wires as seen in the photos so that voltage and ground are available across the full length of all rails.)
  9. Connecting wires for the whole circuit

(To save a bit of money, you may use 100 Ohm resistors for the LEDs instead of 470 Ohm resistors if you prefer.)

Build the Circuit

Follow the provided circuit diagram to build the circuit. It is cramped as there are a lot of components on the single board. This is a prototype on a breadboard to get the game working. You may need to move things around a bit to accommodate everything on the breadboard. The size of the Nano in the diagram isn't quite correct.

A small 8 Ohm speaker sounds MUCH better than a piezo buzzer. However if you're using a speaker, don't put in the 100 Ohm resistor as it will make the speaker too quiet to hear in a room.

Ultimately, you'll likely want to make some kind of permanent circuit with an enclosure and buttons on cables so the players can sit across from each other with the quizmaster at the end of the table. For such a setup, just replace the little board-mount buttons with nicer momentary contact buttons that just connect in the same relative place in the circuit as the current buttons. NOTE: Do not make your cables more than 4 feet long. Long cable lengths can start to produce 'induced resistance' which could cause false button presses. If you need really long lengths, you may need to use some diodes to prevent the induced resistance. Four foot lengths are absolutely fine for teams sitting across from each other at a table with the quizmaster at the head of the table.

Double-check your wiring. You don't want to short things out and damage the Arduino.

Load the Arduino Sketch

Upload the attached sketch to the Arduino.

You'll hear some beeps from the speaker.

Open the Serial Monitor. The beeps will play again and you'll get a welcome message. The game is now on.


Downloads

Playing the Game

On startup, the game resets with scores of zero.

When you see, "Board is OPEN" on the screen, it means players can try buzzing in.

Once a player buzzes in, their LED lights up and the buzzer plays. The screen displays which player buzzed in.

NO OTHER PLAYERS can buzz in yet. The board is LOCKED.

If the player gives the correct response, the quizmaster presses the 'Score' button. The buzzer stops, the LEDs go OFF and 10 points are added to the team's score and the updated scores are displayed on the screen. The board is then OPEN again for players to buzz in.

If the player gives an incorrect response, the quizmaster presses the 'Cancel' button. The buzzer stops and the LEDs go OUT. The board is then OPEN again for players to buzz in.


To play a new game, just press the Reset button on the Arduino and the whole sketch will restart with zero scores.


HAVE FUN!

Getting Fancy - Build a Graphical Interface for the Game

It's fun to have a TV-style scoreboard on your projector as the game progresses.

To do this, it's necessary to build a Graphical User Interface that connects to the Arduino over the Serial (USB) port.

I designed an interface in the past using the Processing language (www.processing.org). Processing is a Java-like beginner-friendly programming language that is able to communicate with the Arduino. It's available for Windows, Mac and Linux.

If you look at Lesson 6 - Communications between Arduino and a Computer running Processing in my Introductory Arduino Course , it takes you through how to build a Processing sketch that reacts to button presses on an Arduino and can send codes to the Arduino from the Processing sketch.

Alternatively, you may use Python or any other language that has the ability to do serial communications.

Have fun! My students loved having a buzzer set for their club meetings and Reach for the Top (like Quiz Bowl, but Canadian) tournaments.


NOW GO MAKE SOMETHING WONDERFUL!!!