Holographic Home Display

by ccmast in Workshop > Home Theater

935 Views, 0 Favorites, 0 Comments

Holographic Home Display

This project guides the user through constructing a 3D holographic video chamber and enclosure. It employs Pepper's ghost effect and specialized holographic videos found on YouTube.

Supplies

Material List

Cardboard — 20ft² (recycled)

Acrylic — 12in x 12in sheet

Small Monitor — 7 in display

Speakers — small

Paint — Spray Can

Tape — Roll of Packing Tape

Enclosure Construction Step 1

Using recycled cardboard create two 8” x 8” squares for the base and top of the enclosure.

Enclosure Construction Step 2

Using recycled cardboard create four 8” x 10” rectangles for the walls of the enclosures.

Enclosure Construction Step 3

On three of the 8”x10“ rectangles cut a 7” x 3” rectangle with the base 4” from the bottom of the rectangle.

Enclosure Construction Step 4

On one of the three rectangles from step 3 cut a 3” diameter circle centered 1.71” from the bottom of the rectangle. 

Enclosure Construction Step 5

Cut a 1.5” x 0.125” rectangle 1” from either side and 3” from the bottom on the uncut panel from step two and the cut panel from step 4. 

Enclosure Construction Step 6

On all 8” x10” panels cut a 1.5” x 0.125” rectangle 2.62” from the top edge and 3.25” from the left edge. 

Enclosure Construction Step 7

Using recycled cardboard create two 9” x 2.5” rectangles and a 9” x 9” square for interior supports

Enclosure Construction Step 8

Cut a 0.5” x 0.5” square out of each corner of the 9” x 2.5” rectangles

Enclosure Construction Step 9

Cut a 3” x 0.48” rectangle out of each outside corner of the 9” x 9” square 

Enclosure Construction Step 10

Cut a 5.45” x 5.45” square out the center of the 9” x 9” square

Enclosure Construction Step 11

Assemble the 4 8”x10” rectangles around the 8” x 8” base square taping the horizontal edges

Enclosure Construction Step 12

Slot in internal support structure pieces 

Enclosure Construction Step 13

Tape the vertical edges and move on to creating the 3D Projection/Holographic Chamber

3D Projection/Holographic Chamber Construction Step 1

On a piece of 12”x12” acrylic mark out a 12” x 3” rectangle 

3D Projection/Holographic Chamber Construction Step 2

Using a box cutting or other razor blade-based knife cut along this line approximately 10 times 

3D Projection/Holographic Chamber Construction Step 3

Place the edge of the scored line against a sharp edge and while holding one side on a counter or table break the other side over

3D Projection/Holographic Chamber Construction Step 4

Using the other square edge of the 12” x 12 “sheet repeat steps 2 and 3 

3D Projection/Holographic Chamber Construction Step 5

Mark a 5.45” line from one corner of the square edge of the broken piece. 

3D Projection/Holographic Chamber Construction Step 6

Mark a 1.5” line on the other edge 1” from the corner used in step 5

3D Projection/Holographic Chamber Construction Step 7

Connect these lines together using a straight edge and repeat steps 2 and 3 to create angle breaks.

3D Projection/Holographic Chamber Construction Step 8

Repeat steps 5-7 three more times to create all the chamber components. 

3D Projection/Holographic Chamber Construction Step 9

Connect four finished pieces together to form the 3D Projection/Holographic Chamber

Final Assembly and Use Step 1 (Optional)

Paint the enclosure with black spray paint to increase contrast and user experience

Final Assembly and Use Step 2

Place the Speaker Inside the designated space and cut holes in the back or side to route the 3.5mm audio cable

Final Assembly and Use Step 3

Cut holes in the back or side to route HDMI and USB wiring for LCD and mount using cardboard standoffs in the enclosure

Final Assembly and Use Step 4

Place the screen into mounts created in Step 2 and route the wiring

Final Assembly and Use Step 5

Place 3D Projection/Holographic Chamber into top retention structure on top of the screen 

Final Assembly and Use Step 6

Place the top on the enclosure and secure with tape 

Complete Testing

Enjoy the Experience!