Futuristic Weighted Chess Set

by SparkBark in Workshop > 3D Printing

333 Views, 1 Favorites, 0 Comments

Futuristic Weighted Chess Set

I've been roaming MakerWorld and Printables lately and stumbled across the community's large collection of stylized chess. Unlike traditional sets, the 3D-printed chess set landscape is extremely varied and creative. I was amazed at all the different styles: organic, Voronoi, hexagonal, geometrical, spiral, among others. I was inspired by these designs, and decided to take my own spin on the traditional chess set.

For this design, I wanted to lean into a pentagonal style. Although there are many hexagonal chess sets, I wanted a bit of a challenge to create something new. A pentagon's asymmetry is a real challenge when modeling the pieces, but it is also be a benefit if done right. It creates a defined, pointed front and a flat back that you can use to create asymmetrical pieces, like the Knight and King.

Supplies

  1. Square Picture Frame: I used a 15 x 15 in. hard plastic frame I had lying around. The frame should be a material you can cut a rim into. The hard plastic was a bit tricky for me, but I could roughly cut it with a pocket knife (or try a plastic knife cutter). Wood may be a better choice if you have the right tools.
  2. Armour Etch: This glass etching cream worked wonderfully to etch the checkerboard pattern onto the glass frame.
  3. Gloves: For the Armour Etch
  4. Brush: If you don't have one already, you'll need a small painter's brush for the Armour Etch. (You can buy the Armour Etch as a kit, but any regular brush will do)
  5. Felt: For the bottom of the chess pieces, so it doesn't scrape the glass. This is also used to cushion the glass when we put it back into the frame.
  6. 3D Printer:
  7. Two PLA Colors: Although black-and-white is traditional, I used light blue and white to go with a cyber-like aesthetic.
  8. Sand: Regular beach sand will work. This adds weight to the 3D prints.
  9. Elmer's Glue: To mix into the sand.
  10. Painter's Tape: To block off sections of the glass
  11. Isopropyl Alcohol: For cleaning the glass; you can also use glass cleaner
  12. Window Cleaner
  13. Ruler, Pencil, etc.

Preparing the Glass

Picture frames always come with a square glass pane, ready to be designed. Let's start by etching the checkerboard pattern into that glass picture frame. Before we do, though, make sure that you have soda-lime glass. It's a very common glass that has hints of green on the edges. If a picture frame is acrylic or plexiglass, the etching won't work.

  1. Use painter's tape (or scotch tape) to make an edge around the glass. This will be used as our measurements
  2. Measure the total length of the glass (This will be different than the advertised length and width)
  3. Figure out the size of your squares. Make sure to consider how big your glass is, and how big you want your border. This may take some trial and error since there's no universal border size, but here's a simple formula to help get a general idea:
  4. Measure the total length of the glass.
  5. Roughly figure out the length you want from the edge to the first line of squares. This will be half your border length.
  6. (Total length - border length[x2]) / 8
  7. Mark your border and each square on the painter's tape.

Measure once, and then measure again just to be sure! I didn't measure both sides and ended up with a larger side, so it's really important to measure right.

Covering for the First Etch

To make the full checkerboard pattern, we will have to etch the board twice. For the first etch, it may be helpful to sketch it out on a piece of paper first.

  1. If needed, tear the painter's tape in half so the width is small enough to fit each square
  2. Identify the first square you want to etch. For me, that was the top right square.
  3. Starting from the square next to the identified square, begin taking strips of painter's tape and layering it in lines from your top marking, to the bottom marking.
  4. Continue this process until all the non-etched squares are covered up lengthwise.
  5. Repeat the process widthwise.
  6. Cover up the border

After this, you should be left with 16 squares in a 4x4 pattern, slightly offset.

Applying the Etching Cream

For the actual etching process, you'll want a well-ventilated area due to the fumes from the etching cream (it smells like rotten eggs). Set up a table that you don't mind getting messy, and make sure you have extra paper towels to clean up everything. It's also a good idea to test the cream on a small, inconspicuous part of the glass first before committing to the entire 4x4 grid.

  1. Make sure to read all the instructions for the etching cream and put on gloves, and follow the safety procedures that are in the instructions: you don't want the cream to stay on your skin
  2. Prepare the glass by cleaning off any smudges or oil that may be on the glass with Isopropyl alcohol
  3. Start a timer for 15 minutes. You may want a shorter etching time, but I've found that 15 minutes generally gives a great result and makes sure there is enough contrast between the frosted and clear squares
  4. Start lightly brushing the etching cream onto each square. Try to apply it to the entire square all at once. If you dab it into the middle and then spread it out, the middle will be unevenly etched compared to the whole square.
  5. Make sure each square has a decent amount of cream (but not too much), according to the photos. you should use more than half of the 8oz bottle.
  6. If you've filled all the squares before the 15 minute timer goes off, go over it again and mix up the cream in each square.

Taking Off the Etching Cream

Once you've applied all the cream and the timer goes off, you can take off the cream. Since we will use the cream at least two more times, make sure to put it back into the same bottle to re-use for later.

  1. Use the brush to pick up the cream and put it back into the bottle
  2. Once you've put as much as you can into the bottle, use a paper towel to clean off some of the residue
  3. Carefully take the glass and take off all of the painter's tape
  4. Carefully run it under water to remove the rest of the residue. The water makes the etching appear to go away, but don't worry! Once it dries, the etching will reappear.
  5. carefully put the glass on a soft surface to dry.

Second Etching and Border

Use the etchings you've just made as a guide for covering the glass again. Repeat the covering process, using strips of painter's tape to cover the squares you just etched. Then, etch and rinse just like before.

For the border, I eyeballed the etching gap and covered each outside border. For the inside, you'll want to be a bit more precise. Use the etched squares to attach a straight piece of tape to the inside of the board. Repeat for the rest: be careful of the inside edges.

Once your happy with your border, carefully etch it and wait another 15 minutes before taking the etching cream off.

Carving Out the Frame and Adding Felt

The one downside to using a picture frame is that the glass is set below the frame. If we wanted to a game of chess, the glass board would be much lower than the highest point of the frame. Every time you want to move a piece, you would have to reach down farther than what is normal.

To fix this, we need to put the glass on top of the frame by carving out a notch around the entire frame for the glass to sit in:

  1. Set the glass on the top of the frame and trace around it with a pen or marker
  2. Take a pocket knife or plastic knife cutter and cut a small notch into the frame, using the markings from the last step as your guide. Go in a consistent distance, and check when necessary.
  3. Try putting the frame in and see where it is overhanging. (Be careful not to put too much pressure on the glass!)
  4. Cut excess frame until the glass fits into the top of the frame.

For the felt cushion, cut long strips of felt and use Elmer's Glue on the notch to attach the felt. Work your way around the frame, gluing and cutting until you fill in the entire notch. Then, use scissors or a knife to cut away excess felt.

With that, the frame and board are done!

Modeling the Chess Pieces

For the chess pieces themselves, I went with a pentagon approach. I started with the base, and kept that same futuristic, sharp-line style throughout. You can get my modeled chess pieces here, or create your own. If your modeling them yourself, here are a few tips:

  1. Use inspiration online. I liked the hexagonal and minimalist style of chess sets, so this gave me inspiration.
  2. Find a style and keep it the same throughout each piece. Every piece should have the same theme. In my model, you can see this especially with the Knight piece. The horse isn't curved; instead it has a rough polygon outline.
  3. Pawns are shortest; Kings are tallest. Make sure each piece is taller than the one before. The Knight, Rook, and Castle are each unique hights
  4. Broaden the base of each piece. Same with the height; each piece must have a specific base width.
  5. Make a simple chessboard to scale the pieces to. This will help you see the proportions of each piece in the broader picture


Printing the Models

To print the models, I used the open-source slicer software Cura. For settings, I would suggest:

  1. Infill: Lightning, 5%. I tried gyroid, but decided against it because the grains of sand were too big for some of the upper parts of the model
  2. Walls: 5. Since I barely did any infill and filled the models with sand later, it is crucial to have a good number of walls so the model doesn't bulge outward.
  3. First layer: No. The model can't have a bottom part; otherwise, we won't be able to fill it with sand.
  4. Supports: Automatic. I needed supports for Knight and the cross of the King.

Adding Weight

Before we fill up all our pieces with sand, we first need to make a sand-glue mixture to seal the top of our pieces.

  1. Fill a small container with sand.
  2. Combine 50% water and 50% Elmer's glue into a mixture
  3. Pour into the smaller container, mixing well until the sand has a clay-like texture.

Now, fill up each piece almost to the top. dap a genourous ammount of sand-glue into the gap at the top, and carefully spread it out. Make sure to gently shake the piece and pack down the sand to avoid any air gaps.

Felt Bottoms

Because we are working with glass, we need to make sure there is cushioning between the plastic pieces and the glass. Simply trace out the base of each piece onto a piece of felt and cut them up. Once all the pieces are ready, you can glue the felt onto the underside of each piece.

Final Touches

  1. If needed, carefully wash the pieces to get the dirt off them. This was the most rewarding part of the whole project, since I got to see the pieces fully pieced together and clean for the first time.
  2. Find a bag for your pieces. I used a felt bag and drew a geometric king on it using regular Sharpies.

That's it! Thank you for reading to the end of this Instructable, and I hope this inspires you to go out there and make something cool to share with the world! Big projects like these may look intimidating to start, but the reality is that every project can be split up into pretty simple parts. When the finished product is broken down into manageable pieces, it becomes much easier to complete. The hardest part, I've learned, is the first step. After that, you just keep on making until you reach your goal.