Driving the First WS2812b LED With AVR Assembly

by BoboacaC in Teachers > K

327 Views, 1 Favorites, 0 Comments

Driving the First WS2812b LED With AVR Assembly

I believe that every student approaching computer science should experience a fundamental milestone at least once: discovering that behind the software lie real hardware registers, made of physical bits that can only be either 0 or 1.

You don't need to become an Assembly programmer, nor do you need to use machine language on a daily basis.

It is enough, just once, to take a simple microcontroller like the ATmega328, open its datasheet, locate a hardware register, and consciously change one of its bits to witness the direct, physical effect on the hardware.

That experience changes your mindset forever.

From that moment on, the computer is no longer a black box.

You truly understand that every function, every library, every framework, and every high-level programming language ultimately achieves the exact same goal: they write registers, read registers, and manipulate bits.

The ATmega328 holds immense educational value precisely because it makes this process visible and intuitive. Its architecture allows students to see a direct, unbroken line between a single bit written into a register and an immediate physical reaction.

This understanding is not just about programming a microcontroller.

It is about understanding how computer science works at its core.

Technical education should not be limited to teaching how to use increasingly complex tools. It should also provide the conceptual foundation to comprehend the physical reality hidden beneath software abstraction.


WS2812/WS2816 LEDs are individually addressable RGB LEDs. Each LED is controlled via a single data line using a specific timing protocol.

This example shows how to light the first LED in full white using direct AVR assembly, without any library. It’s a great way to understand how the protocol works at the cycle-accurate level.

Supplies

Hardware:

  1. Arduino Nano/Uno (ATmega328p)
  2. 1 WS2812B LED
  3. Jumper wires
  4. Optional: 470Ω resistor on the data line for signal stability

Software Tools:

  1. AVR Compiler JS (Web-based compiler and uploader)

Understanding the WS2812/WS2816 Protocol


  1. T0H = high time for a “0”
  2. T1H = high time for a “1”
  3. Reset = low > 50 µs to latch data into LED
⚠️ Timing is critical: if HIGH/LOW durations are off, the LED will misinterpret the data.

The Delay Loop Code


1️⃣ The delay loop code


ld_loop:
nop ; 1 CPU cycle (~62.5 ns at 16 MHz)
nop ; 1 CPU cycle (~62.5 ns)
dec r16 ; decrement r16 (~1 cycle)
brne ld_loop ; branch if r16 ≠ 0 (~2 cycles if taken, 1 if not)
ret ; return (~4 cycles)
  1. CPU frequency: 16 MHz → 1 cycle = 62.5 ns
  2. nop = 1 cycle
  3. dec = 1 cycle
  4. brne = 2 cycles when branch is taken, 1 cycle when not
  5. ret = 4 cycles (only at the end of the loop)


How It Creates HIGH/LOW Time

Example for HIGH: r16 = 14

  1. Each iteration of the loop while r16 ≠ 0 lasts approximately:

nop + nop + dec + brne (taken) = 1 + 1 + 1 + 2 = 5 cycles
  1. Number of iterations = 14
  2. Total time = 14 × 5 cycles × 62.5 ns ≈ 4.375 µs

⚠️ In practice, the exact timing is empirically tuned, so using 14 for HIGH and 12 for LOW gives ≈0.7 µs HIGH and ≈0.6 µs LOW at 16 MHz.


⚠️ The Reality Check: Where Theory Meets Practice

If a student connects an oscilloscope to the data pin, they will discover something shocking: the actual HIGH duration is not 4.375 µs, but approximately 0.7 µs.

Why does this happen? This gap is the most valuable lesson this project can teach. In computer engineering, textbooks describe a perfect world, but the physical hardware operates under real physical constraints:

  1. Subroutine Overhead: The rcall and ret instructions, along with bit-manipulation commands (sbi/cbi) in the main loop, alter the signal timing while the processor shifts registers.
  2. Parasitic Capacitance: Real microcontroller pins behave like tiny capacitors. Charging and discharging the line rounds off the edges of the square wave, slowing down the signal.

The Verdict

Empirical tuning is the core of low-level hardware development. By setting 14 for the HIGH state and 12 for the LOW state, the timing aligns perfectly with the WS2812B protocol windows:


This experiment proves that a computer is not a magical black box: behind every line of code lies a real circuit dictated by physics.

WS2816 Bit Timing Principle


WS2816 reads a bit based on the HIGH pulse duration:

  1. ~0.7 µs HIGH → bit “1”
  2. ~0.35 µs HIGH → bit “0”

The LOW period completes the bit and ensures a total bit period of ~1.25 µs, which is required by WS2816.


Example: Sending a “1” Bit


| Action | Pin | Delay (r16) | Approx. Time |
| -------- | --- | ----------- | ------------ |
| Set HIGH | PB0 | 14 | 0.7 µs |
| Set LOW | PB0 | 12 | 0.6 µs |


  1. Total time per bit ≈ 1.3 µs, which is within WS2816’s spec (1.05 – 1.45 µs)

Repeating this 24 times sends one LED in full white.

The Avr Asm Code



; first LED on ws2816 high white

.org 0
rjmp init ; reset vector -> jump to program start

.org 0x68 ; (arbitrary start address depending on flash map)
init:
sbi 4,0 ; set bit in I/O register: DDRB0 = 1 (set PB0 as output)

loop:

ldi r17,24 ; number of bits to send = 24 (1 LED x 24 bits)
sus:
; --- BIT "1" routine ---
; total time per bit = 1.25 µs ± 250 ns (valid range 1.05 – 1.45 µs)

sbi 5,0 ; set pin high = start of bit
ldi r16,14 ; delay for HIGH period (~700 ns, range 500–850 ns)
rcall ld_loop ; wait loop for HIGH

cbi 5,0 ; clear pin low = end of HIGH
ldi r16,12 ; delay for LOW period (~600 ns, range 450–1000 ns)
rcall ld_loop ; wait loop for LOW

dec r17 ; decrement bit counter
brne sus ; if not zero, send next bit

; --- Reset frame ---
; needed to latch data into WS2816 LEDs
rcall ld_loop ; here used as reset delay (>50 µs)
rjmp loop ; repeat the process forever

; ----------------------------------------------------
; Subroutine: ld_loop
; Provides a simple delay
; Each iteration ≈ 50 ns (at 16 MHz)
; Input: r16 = loop count
; ----------------------------------------------------
ld_loop:
nop ; no operation (~62.5 ns each at 16 MHz)
nop
dec r16
brne ld_loop ; repeat until r16 = 0
ret


Launch the experiment with AVR1 by CostyCNC!


By clicking this https://costycnc.github.io/avr-compiler-js/?code=ws2812.txt, you will instantly open the web compiler with the WS2812 Assembly code preloaded and ready to be flashed onto your board.

How to proceed:

  1. Use the right browser: Open the link using Google Chrome or Microsoft Edge.
  2. Connect your board: Plug your Arduino into the computer via USB cable.
  3. Flash the code: Click the upload button on the web page.

The tool compiles the HEX file instantly and sends it to your Arduino via Web Serial API, without requiring any IDE or software installation on your PC.