Creature Showtime
Uma vestimenta simulando a lenda da curacanga, com habilidade de transformar a cabeça que se solta do seu corpo em uma bola de fogo
Supplies
Arduino Uno
Motor Redutor
Botão
Fita LED
Tnt (tecido)
Isopor
Bateria Moeda
Cabo Macho Fêmea
Relés
Confecção Da Vestimenta
- Faça as medidas e corte o tecido.
- Junte usando costura e/ou cola quente.
- Molde um isopor para dar a sustentação da cabeça do personagem.
Firmware
// ==========================================
// PROJETO: MOTOR + RELES + FITA LED RGB
// ARDUINO UNO + SISTEMA DE LOG
// ==========================================
// BOTOES
const int botao1 = 2;
const int botao2 = 12;
const int botao3 = 4;
// RELES DO MOTOR
const int rele1 = 8;
const int rele2 = 9;
// FITA LED RGB
const int ledR = 5;
const int ledG = 6;
const int ledB = 10;
// ESTADO DA FITA
bool estadoLED = false;
// LEITURA ANTERIOR DOS BOTOES
bool anteriorBotao1 = HIGH;
bool anteriorBotao2 = HIGH;
bool anteriorBotao3 = HIGH;
// CONFIGURACAO DOS RELES
const int RELE_LIGADO = LOW;
const int RELE_DESLIGADO = HIGH;
// ==========================================
// FUNCAO PARA DESLIGAR O MOTOR
// ==========================================
void desligarMotor() {
digitalWrite(rele1, RELE_DESLIGADO);
digitalWrite(rele2, RELE_DESLIGADO);
Serial.println("[MOTOR] Motor desligado.");
}
// ==========================================
// FUNCAO PARA CONTROLAR A FITA RGB
// ==========================================
void atualizarLED() {
if (estadoLED == true) {
digitalWrite(ledR, HIGH);
digitalWrite(ledG, LOW);
digitalWrite(ledB, LOW);
Serial.println("[LED] Fita ligada - COR VERMELHA.");
} else {
digitalWrite(ledR, LOW);
digitalWrite(ledG, LOW);
digitalWrite(ledB, LOW);
Serial.println("[LED] Fita desligada.");
}
}
// ==========================================
// CONFIGURACAO INICIAL
// ==========================================
void setup() {
Serial.begin(9600);
Serial.println("================================");
Serial.println(" SISTEMA INICIADO");
Serial.println(" MOTOR + RELES + FITA RGB");
Serial.println("================================");
// BOTOES
pinMode(botao1, INPUT_PULLUP);
pinMode(botao2, INPUT_PULLUP);
pinMode(botao3, INPUT_PULLUP);
// RELES
pinMode(rele1, OUTPUT);
pinMode(rele2, OUTPUT);
// FITA RGB
pinMode(ledR, OUTPUT);
pinMode(ledG, OUTPUT);
pinMode(ledB, OUTPUT);
// ESTADO INICIAL
digitalWrite(rele1, RELE_DESLIGADO);
digitalWrite(rele2, RELE_DESLIGADO);
atualizarLED();
Serial.println("[SISTEMA] Inicializacao concluida.");
}
// ==========================================
// PROGRAMA PRINCIPAL
// ==========================================
void loop() {
// LEITURA DOS BOTOES
bool leitura1 = digitalRead(botao1);
bool leitura2 = digitalRead(botao2);
bool leitura3 = digitalRead(botao3);
// LOG DOS VALORES DOS BOTOES
Serial.print("[BOTOES] B1: ");
Serial.print(leitura1);
Serial.print(" | B2: ");
Serial.print(leitura2);
Serial.print(" | B3: ");
Serial.println(leitura3);
// ----------------------------------------
// BOTAO 1: MOTOR SENTIDO 1
// ----------------------------------------
if (leitura1 == LOW && anteriorBotao1 == HIGH) {
Serial.println("[BOTAO 1] Pressionado.");
Serial.println("[MOTOR] Sentido 1 selecionado.");
desligarMotor();
delay(100);
digitalWrite(rele1, RELE_LIGADO);
digitalWrite(rele2, RELE_DESLIGADO);
Serial.println("[RELE] Rele 1 acionado.");
}
// ----------------------------------------
// BOTAO 2: MOTOR SENTIDO 2
// ----------------------------------------
if (leitura2 == LOW && anteriorBotao2 == HIGH) {
Serial.println("[BOTAO 2] Pressionado.");
Serial.println("[MOTOR] Sentido 2 selecionado.");
desligarMotor();
delay(100);
digitalWrite(rele1, RELE_DESLIGADO);
digitalWrite(rele2, RELE_LIGADO);
Serial.println("[RELE] Rele 2 acionado.");
}
// ----------------------------------------
// BOTAO 3: LIGA/DESLIGA FITA RGB
// ----------------------------------------
if (leitura3 == LOW && anteriorBotao3 == HIGH) {
Serial.println("[BOTAO 3] Pressionado.");
estadoLED = !estadoLED;
atualizarLED();
}
// ----------------------------------------
// ATUALIZA LEITURAS ANTERIORES
// ----------------------------------------
anteriorBotao1 = leitura1;
anteriorBotao2 = leitura2;
anteriorBotao3 = leitura3;
delay(100);
}
Circuito
Botões:
- Botão 1 → pino 2.
- Botão 2 → pino 12.
- Botão 3 → pino 4.
- Outro terminal de cada botão → GND.
Relés e motor:
- IN1 → pino 8.
- IN2 → pino 9.
- VCC e GND → alimentação compatível.
- Conecte o motor aos contatos dos relés conforme o circuito de reversão.
Fita LED RGB:
- Vermelho → pino 5.
- Verde → pino 6.
- Azul → pino 10.
- Utilize acionadores e fonte externa adequados.
Programação:
- Conecte o Arduino ao computador.
- Abra a Arduino IDE.
- Insira o código.
- Selecione Arduino Uno e a porta correta.
- Clique em Carregar.
Testes:
- Botão 1: motor no sentido 1.
- Botão 2: motor no sentido 2.
- Botão 3: liga/desliga a fita LED.