Construction Frame Set
I wanted to make a simple construction related project to show how simple shapes or way a structure can stay up during many events like to using a fan. With the amount of ways you can build something, everyone can do something unique that may or may not hold heavy weights.
Supplies
The only materials that are needed in this toy is a 3d printer with filament PLA or ABS recommended. all parts were done with a 3d modeling software, and a little math.
Create Set in 3d Design
If you want to make your own version, here's how to make the basic ones from the file above. First you open you 3d software and create a 1/2 inch circle on a 2d plane. Then extrude out 3 inch to make a cylinder.
Pillar Continue
Next you will create another circle on top that is 0.3inch wide then extrude 0.3 inch to make the top connector. after you got that make a sketch on the side in any way, I created a offset plane to put the sketch on. then create 2 circles, 2.5 inches from the top, and 1/2 inches from the bottom. each circle will be 0.21 inches wide, once that is there extrude out the circles you created to cut a hole straight through the pillar to allow a rod of similar size to fit.
4X4 Platform
To start off the platform you will make a 4 by 4 by 1/2 inch plate. Your platform can be any shape any size, but must be able to have equal distance holes in a grid.
4X4 Slots
To make the holes to fit the pillars I used 2 sketches for simplicity, there will be 2 circles 0.5 squared inches from each corner. One circle will be 0.31 inches and the other will be 0.51 inches. Then extrude the smaller circle first though the entire plate, then extrude the bigger circle only 0.2 inches to make the holes for connections.
For people who want a different size the circles will be the very top and bottom of the pillars diameter plus 0.01 or 0.02 inch tolerance to have a sturdy fit. and the depth of the smallest hole depends on how tall you extruded the top connector of the pillar.
4X4 Adjustments
The next steps to making this plate is to make a sketch on each side(or one side then mirror) of the same holes you made to the side of the pillar, these holes should only extrude to the middle of the top circle, each side will have one for each corner hole. this is optional but cut though the middle of the plate for less cost or to add details or designs.
4X4 Finish
The last step to the platform is the crate a circle for each corner that is the hole size(which is 0.5 in this case) plus 0.3, then extrude. This will make the pillars more secure and adds a bunch of friction.
If you want different platforms, you can follow these exact steps to make new ones. make sure each pillar connection is 3 inches from each others centers.
Angled Pillar
This pillar is going to be used for changing a 4X4 plate to plates that are offset or are out of the ordinary to regular pillars. First you start off by creating 2 sketches, it does not matter height but I used 3 inches for starters. The circles on the 2 sketches will be the same as the original pillars.
PILLAR ANGLE EXTRUSION
Once you got your circles you would want to loft it for a clean connection. the top of the pillar will be the same as the normal pillar so do your 0.3 extrusion at the top and extend the bottom straight down for 0.4 inches to make it connect to holes.
Aligning
The angled pillars are used for platforms extruding from other platforms and not from the ground. But can also be used for making off grid platforms that does not fit with the straight pillars, you can test your unusual shapes to see if they fit or make your own from the pillars set up.
Levels
I set up 3 levels to see who can make the best weight to load ratio, each one restricts you more then the last. But you can also design your own levels, each pillar has to be 3 inches apart(from midpoint to midpoint) in a grid, what I made was a 7x7 grid, 5x5 grid and a 2.5x2.5 grid, from the picture you can see the holes you get. The levels can be in any shape form or size but adds a more challenging approach to the toy.