Concrete Bike Rack System

by valentinomorandi1 in Design > Architecture

3012 Views, 27 Favorites, 0 Comments

Concrete Bike Rack System

Designing for the city means solving real problems with creative, permanent solutions. This instructable documents PAVELO, a concrete bike rack system designed to integrate seamlessly into existing urban sidewalks—replacing standard pavement tiles without requiring complex groundwork or infrastructure changes.

The innovation here is elegant: instead of mounting racks to walls or requiring underground anchoring, PAVELO uses concrete casting to create a unified, durable structure that sits flush with the sidewalk. It's functional, aesthetic, and built to last decades. The project demonstrates industrial design thinking, mold-making, and concrete casting techniques that can be adapted for other urban furniture applications.

Supplies

Design & Prototyping

  1. MDF board (1/2" thickness, depending on design)
  2. Wood cutting tools (saw, CNC or band saw)
  3. Ruler, calipers, measuring tape
  4. CAD software (AutoCAD, SolidWorks, or similar)
  5. Drafting materials

Mold-Making

  1. High-impact polystyrene sheets (HIPS, 2mm thickness)
  2. Thermoforming machine or vacuum former
  3. Mold frame or support structure
  4. Release agent (mold release spray or wax)

Concrete & Casting

  1. Portland cement (gray or white, ~6Kg depends on design)
  2. Fine aggregate/sand (~10-12 kg per unit)
  3. Coarse aggregate/gravel (~8-10 kg per unit)
  4. Water (~2-3 liters per unit)
  5. Concrete mixing equipment (mixer, wheelbarrow, or ready-mix delivery)
  6. Concrete tools (trowel, float, finishing brush)

Hardware & Reinforcement

  1. Steel reinforcement rebar or wire mesh (optional but recommended)
  2. Metal inserts/anchors for bike retention hardware
  3. Stainless steel chain attachment points (welded or bolted)
  4. Anchor bolts or concrete anchors (if ground installation required)

Safety & Finishing

  1. Concrete sealer (outdoor-grade polyurethane or acrylic)
  2. Sandpaper (120-220 grit for finishing)
  3. Safety glasses and dust masks (concrete dust)
  4. Work gloves
  5. High-visibility safety clothing (for installation)

Design Phase & Bicycle Measurements

Understanding the constraints:

  1. Begin by measuring your target bikes:
  2. Average wheelbase (distance between front and rear axles): typically 95-115cm
  3. Tire width at center: 3-5cm
  4. Bottom bracket height (lowest point of frame): 25-35cm
  5. Overall frame geometry and mounting points
  6. Measure the existing sidewalk/pavement:
  7. Standard sidewalk tile width: 60-80cm
  8. Tile depth: 40-60cm
  9. Thickness: 5-10cm
  10. Note the specific tiles you'll replace
  11. Design your rack geometry:Wheel support width: size to accommodate your target wheel diameters (typically 26-29" bikes)
  12. Spacing between wheel support points: 30-40cm minimum
  13. Depth from sidewalk edge: 15-25cm (balancing usability with sidewalk space)
  14. Height above pavement: 8-15cm
  15. Create detailed CAD drawings

Create a Prototype in MDF

Building a full-scale MDF prototype is crucial—it validates your design before expensive concrete production.

  1. Prepare your MDF sheets:
  2. Cut MDF into strips matching your design dimensions
  3. Use a table saw or CNC cutter for precision
  4. Sand all edges smooth (120 grit minimum)
  5. Assemble the prototype:
  6. Build the basic frame structure (the wheel support areas)
  7. Glue and screw pieces together to form the complete shape
  8. Ensure the profile matches your CAD design exactly
  9. Test the prototype:
  10. Place actual bikes against it
  11. Check wheel fit in the support areas
  12. Verify stability and spacing
  13. Adjust dimensions if needed
  14. Take detailed measurements of any successful areas
  15. Photograph the prototype from all angles:
  16. This serves as reference documentation during later steps
  17. Capture the successful design proportions

Apply Polymeric Filler to Prototype

To create a smooth mold surface (rather than exposing MDF grain), seal the prototype:

  1. Prepare the surface:
  2. Sand the entire MDF prototype with 80-120 grit sandpaper
  3. Clean away all dust with a damp cloth
  4. Let dry completely
  5. Apply polymeric filler/putty:
  6. Use a two-part epoxy filler or polyurethane filler
  7. Apply in thin layers (3-5mm) with a putty knife
  8. Focus on filling any gaps, seams, or wood grain
  9. Let each layer cure per manufacturer instructions (typically 4-24 hours)
  10. Sand smooth:
  11. After curing, sand with 120-180 grit sandpaper
  12. Aim for a smooth, glass-like surface
  13. This becomes your mold master
  14. Apply release agent:
  15. Spray or brush a mold release agent onto the entire surface
  16. This prevents the plastic from sticking during thermoforming
  17. Use automotive wax or commercial mold release spray

Create Ventilation Perforations in the Prototype

Before thermoforming, create small air holes that allow vacuum pressure to work effectively during the forming process:

  1. Why ventilation matters:
  2. During vacuum thermoforming, air must escape from underneath the plastic sheet
  3. Without proper ventilation, air pockets trap under the plastic, creating bubbles and incomplete mold formation
  4. Small perforations ensure the plastic conforms smoothly to every detail of your prototype
  5. Drill ventilation holes:
  6. Use a drill press with a small bit (2-3mm diameter)
  7. Create a grid pattern across the top surface of the prototype
  8. Space holes approximately 30-40mm apart (roughly every 1.5 inches)
  9. Avoid placing holes directly in critical detail areas where perfect contact matters most (like the wheel support edges)
  10. Typical count: 20-30 holes depending on prototype size
  11. Ensure proper air flow:
  12. Holes should penetrate completely through the MDF
  13. Check that air can flow freely—no blockages from dust or debris
  14. During thermoforming, these allow air to escape, creating a tight seal between plastic and prototype surface
  15. Plan metal insert locations separately:
  16. While marking holes, also mentally note where metal anchor points will go (typically 2-4 per wheel support area)
  17. You'll position these inserts after the mold is thermoformed (see Step 6)

Thermoform the Mold

Using a vacuum thermoforming machine, create a negative mold from your MDF master:

  1. Prepare the thermoforming machine:
  2. Heat the high-impact polystyrene (HIPS) sheet to its softening point (~170-180°C)
  3. This typically takes 3-5 minutes depending on sheet thickness (2mm HIPS)
  4. Position the master prototype:
  5. Secure the MDF prototype under the heated plastic sheet
  6. Ensure it's centered and stable
  7. Apply vacuum:
  8. Lower the heated plastic onto the prototype
  9. Activate the vacuum to draw the plastic down tightly
  10. Hold for 1-2 minutes until the plastic cools and sets
  11. The plastic will conform to every detail of the prototype
  12. Remove the mold:
  13. Once cooled, carefully remove the thermoformed plastic mold
  14. You now have a negative mold of your design
  15. Trim and reinforce:
  16. Trim excess plastic from the edges
  17. Add reinforcement ribs or support structures to the underside of the mold
  18. These prevent the mold from flexing during concrete pouring

Create Metal Insert Anchors

These anchor points allow bikes to be secured with chains or straps:

  1. Prepare metal inserts:
  2. Use stainless steel or galvanized steel anchor points
  3. Typical specifications: 1/2" diameter, 10-15cm long
  4. Weld or bolt attachment hardware (D-rings, eye bolts, or threaded inserts)
  5. Position inserts in the thermoformed mold:
  6. Using your marked reference points from Step 4, position metal inserts in the plastic mold
  7. Secure them in place with temporary holders or adhesive putty
  8. Verify alignment and spacing
  9. The inserts should protrude slightly above the mold surface to be cast into the concrete
  10. Ensure proper spacing:
  11. Metal anchors should be positioned to withstand forces from bike weight and pulling
  12. Minimum 50-80mm from edges
  13. At least 150mm apart to prevent stress concentration

Prepare the Casting Area & Mix Concrete

Before pouring, prepare your workspace:

  1. Set up the casting station:
  2. Place the thermoformed mold on a level, stable surface
  3. Support the mold from underneath with blocks or bracing
  4. Ensure drainage (concrete will weep water during curing)
  5. Have concrete tools and cleaning supplies nearby
  6. Prepare concrete mix:
  7. Mix proportions: 1 part cement : 2-3 parts fine sand : 3-4 parts coarse aggregate
  8. Example (per single bike unit): 5 kg cement + 10-12 kg sand + 8-10 kg gravel + ~2.5 liters water
  9. Total per unit: approximately 23-27 kg of concrete
  10. Use a concrete mixer to blend thoroughly until uniform
  11. Adjust for your conditions:
  12. For denser, stronger concrete: reduce water, increase cement
  13. For easier pouring: slightly increase water (but don't exceed 0.5 water-to-cement ratio)
  14. Test batch on scraps of concrete mix to verify color and consistency
  15. Plan for reinforcement:
  16. If using rebar or wire mesh, pre-position it inside the mold before pouring
  17. This adds structural strength for heavy bike load

Pour Concrete & Cast the Bike Rack

  1. Prepare the mold:
  2. Place release agent in the mold (thin coat of spray release or soap solution)
  3. This prevents the concrete from permanently bonding to the plastic
  4. Pour concrete:
  5. Begin pouring concrete from one end of the mold
  6. Pour steadily to avoid trapping air pockets
  7. Fill the mold completely, ensuring all corners and crevices are filled
  8. Vibrate to remove air:
  9. Use a concrete vibrator to settle the mix and remove trapped air
  10. Alternatively, gently tap the mold sides with a rubber mallet
  11. This improves strength and surface quality
  12. Strike off excess:
  13. Use a straight edge (wood board) to level the top surface
  14. Remove excess concrete flush with the mold edges
  15. Initial curing (first 24 hours):
  16. Cover with plastic sheeting or wet burlap to retain moisture
  17. Protect from direct sun and rapid drying
  18. Do not disturb or vibrate

Demolding & Initial Finishing

After 24-48 hours:

  1. Remove from mold:
  2. Carefully flex and separate the thermoformed plastic mold from the concrete
  3. If resistance is met, spray a little water around the edges to help release
  4. Gently peel back the mold
  5. The concrete should be firm but not fully hardened at this stage
  6. Clean the surface:
  7. Remove any excess concrete burrs or rough spots
  8. Use a concrete float or trowel to smooth the surface
  9. Wipe with a damp sponge for a cleaner finish
  10. Check metal inserts:
  11. Verify all metal anchors are properly embedded and accessible
  12. Clean any concrete splatter from insertion points
  13. Initial curing continues:
  14. Return the casting to a curing area
  15. Keep it damp by misting with water 2-3 times daily for 7 days
  16. Concrete reaches ~70% strength after 7 days, full strength after 28 days

Finish the Concrete Surface

After 7 days of curing:

  1. Sand the surface (optional):
  2. Use 120-180 grit sandpaper to smooth any remaining rough spots
  3. This reveals the aggregate and creates a polished look
  4. Creates better aesthetic appeal
  5. Apply concrete sealer:
  6. Use an outdoor-grade polyurethane or acrylic sealer
  7. This protects the concrete from:
  8. Water infiltration and freeze-thaw damage
  9. Salt and deicing chemicals (in winter climates)
  10. Staining from bike oils and dirt
  11. Follow sealer manufacturer's instructions for application and curing
  12. Final inspection:
  13. Check for any cracks or defects
  14. Ensure all anchor points are functional
  15. Test bike placement and clearances one final time

Installation (If Ground-Fixed)

If your design requires anchoring to the ground:

  1. Prepare the installation site:
  2. Remove existing pavement tiles carefully
  3. Level the base
  4. If needed, create a concrete pad foundation for the bike rack to sit on
  5. Positioning:
  6. Place the finished concrete bike rack in the prepared location
  7. Ensure it's level and properly oriented
  8. Check alignment with surrounding pavement
  9. Anchoring options:
  10. Option A: Simple placement (if heavy enough, ~150+ kg)
  11. Option B: Anchor bolts through pre-drilled holes into a concrete base
  12. Option C: Epoxy-set anchor bolts directly into the installed bike rack
  13. Safety check:
  14. The structure must withstand a tipping force (bikes leaning, people pushing)
  15. Minimum 400-500 kg total weight is recommended

Maintenance & Long-Term Care

Your concrete bike rack is built to last 30+ years:

  1. Regular inspection:
  2. Check for cracks or spalling (concrete surface deterioration)
  3. Inspect metal anchors for rust or looseness
  4. Clean debris from wheel support areas
  5. Cleaning:
  6. Pressure wash quarterly to remove dirt and algae
  7. Wipe down attachment points to prevent corrosion
  8. Sealer reapplication:
  9. Reapply concrete sealer every 3-5 years
  10. This maintains water resistance and appearance
  11. Safety maintenance:
  12. Ensure metal anchors remain tight and secure
  13. Replace any corroded hardware with stainless steel equivalents
  14. Monitor for structural movement or settlemen


Design Variations & Scaling

This design can be adapted for:

Different bike styles:

  1. E-bikes (wider, heavier): increase support thickness and width
  2. Mountain bikes with wide tires: widen wheel support areas
  3. Cargo bikes: add reinforcement for heavier loads

Different quantities:

  1. Single-bike racks: shrink the footprint
  2. 8-10 bike racks: expand length, maintain support structure

Material variations:

  1. Colored concrete (add pigments to cement mix for urban aesthetics)
  2. Exposed aggregate finish (for visual interest)
  3. Imprinted patterns (during casting, press textures into the surface)

Climate considerations:

  1. Cold climates: increase concrete thickness and reinforcement to resist freeze-thaw
  2. Wet climates: emphasize sealing and drainage
  3. High-salt environments (near ocean): use marine-grade epoxy sealer


Final Thoughts

This was a great academic project because it forced me to think through every step—from the initial CAD design all the way to pouring and finishing concrete. The combination of digital design, prototype building, and hands-on manufacturing is exactly the kind of work that makes maker projects valuable.

If you build your own version, you'll end up with a genuinely useful concrete structure. And you'll know exactly how it was made—every step.


Keywords for Instructables

concrete, urban design, bike rack, sidewalk furniture, thermoforming, cement casting, CAD design, industrial design, public infrastructure, sustainable design, mold-making, prototype, concrete finishing, sealer, anchor installation, MDF prototyping, academic project, maker education