Christmas Tree PCB Gift
It was in the middle of september where i wanted to do a fun little project. Because christmas was approaching and I wanted to give some homemade gifts to my family I choosed to do a christmas tree.
The christmas tree should:
- must be power efficient
- not be larger than 10*10cm
- programmable
- must have a base, where the battery is placed
- must have more than 1 mode of operation
I designed the PCB in Altium Designer, printed the PCBs on JLC, programmed the atmel microcontroller in Atmel Studio 7.0 and designed the 3d model in SolidWorks.
The Plan
My plan is to design 2 christmas tree shaped pcbs.
Before I started to work on the schematics I choosed the microcontroller, power supply, led drivers...
For the microcontroller i used the ATTINY85-20SU because of its simplicity (8pins).
For powering the microcontrollers and leds i choosed 3 AA batterys.
For switching the leds i choosed mosfets SI1012CR-T1-GE3.
Designing the PCB
First i made the schematic then the PCB layout.
After i choosed the microcontroller i looked at the datasheet of the controller and the pinout. The microcontroller needed to have a sleep mode and atleast 4 I/O pins for 3 mosfets, one for each color(red,yellow,green) and a push button. The attiny85 was perfect.
Pin1(RESET) - is reset pin, where I connected an 10 kOhmPULL UP resistor (package 1206)
Pin2 - i used this pin for the push button, everytime i pressed the pushbutton the pin got pulled down to ground(so I programmed this pin as input and used an internal PULL UP)
Pin3 - in the SCH1 I did connect this pin on the male header but i didnt used it.
Pin4 - Ground
Pin5(MOSI) - goes to the gate of the mosfet Q3 for yellow leds
Pin6(MISO) - is connected to the gate of the mosfet Q2 for green leds
Pin7(CLK) - connected to the gate of the mosfet Q1 for red leds
Pin8 - Vcc
Datasheet of the mosfet: https://www.vishay.com/docs/67519/si1012cr.pdf
On one mosfet there are 12 leds ( total power consumption for 1 mosfet: P=I*U, P=20mA*4.5V=90mW)
I also added 6 vias(2.54 mm from each other for programming (header 4 and header 2 on the SCH)).
After the SCH i went on arranging the board. I cut out the christmas tree shape, and then I layed out the components.
I added two decoupling capacitors 100pF and 10uF to stabilize the input voltage.
The 100 kOhm resistor that is in SCH i didnt use.
I added the gerber files for both PCBs.
Soldering
I used an old soldering iron I had laying around.
First i soldered all the smd components, then all the through hole components.
After soldering it was time for fun programming :D
Programming
For programming I used the AVRISP mk2 .
Because you need an external power supply to power the microcontroller and programator I connected 5v and gnd from Arduino Mega just for power. Then i connected the programator on my programmable pcb where i connected:
1 pin(RESET) to RESET
4 pin(GND) to GND
5 pin(MOSI) to MOSI
6 pin(MISO) to MISO
7 pin(CLK) to CLK
8 pin(Vcc) to Vcc
I attached the program code.
I the code i implemented pwm control, sleep mode, interupts...
The firs mode is just blinking all the leds, in the second mode i used the pwm to change the brightness(i just need to tweak a little to make it more fluently, the third mode is just turning the led on and off in steps, the fourth mode is just crazy blinking( i used the pwm function like in the second mode) i call it "funky" mode :D
After you press the push button an timer ist started that counts 5 minutes an then goes back to sleep mode( in sleep mode the power consumption is like 2-6 uA)
WARNING!!!
Before you programm your attiny85 with this programm, you need to disable8 Mhz fuse. because if not your attiny85 will work at only 1 Mhz
Downloads
Component List
I ordered components for 12 christmas tree i added an file of components that i ordered from Farnell and Mouser, other components i ordered from aliexpress:
- LEDS
Amazon.de:
- battery
Downloads
3d Modeling
I wont describe how i designed the 3d model for the base, but if you want you can PM me and i send you the files.
I made some opening for the on/off switch and the Push button.
First i soldered some wires on the push button and switch, then i positioned them and hot glued them from the inside of the base, then i cut out the perf boards, and soldered the female connectros and wires together and hot glued everything inside the base.
Summary
Main purpose of this project was that i wanted to suprise my family with something homemade, that was the motivation that helped me to complete it.
Special thanks to my friends that helped me with this project.
I added an excel file, where i calculated how long would the battery last(in ideal conditions).
If you have any questions leave a comment.