Build a Regulated -5V Power Supply Module Using the TI LM7905CT

by robertfletcher1582 in Circuits > Arduino

48 Views, 0 Favorites, 0 Comments

Build a Regulated -5V Power Supply Module Using the TI LM7905CT

Many analog electronic circuits require a stable negative voltage supply to operate correctly. Operational amplifiers, audio preamplifiers, signal-conditioning circuits, and other analog projects often need a negative power rail in addition to a positive supply.

In this project, I will show how to build a simple regulated -5V power supply module using the Texas Instruments LM7905CT three-terminal negative voltage regulator.

The LM7905CT provides a fixed -5V output from an unregulated negative DC input. Its TO-220 package makes it convenient for through-hole assembly, prototyping, and mounting on a heatsink when necessary.

The goal is to create a practical auxiliary power module that can be connected to an existing dual-rail power supply or another suitable negative DC source.

This project is useful for electronics hobbyists, students, and engineers who regularly work with analog circuits and need a dedicated -5V supply.

Supplies

TI LM7905CT -- 1 -- Negative voltage regulator

10µF electrolytic capacitor -- 2 -- Input and output filtering

100nF ceramic capacitor -- 2 -- Local high-frequency bypassing

100Ω, 1W resistor -- 1 -- Output test load

Screw terminal blocks -- 2 -- Input and output connections

Perfboard -- 1 -- Circuit assembly

TO-220 heatsink -- 1 -- Thermal management

Insulated hookup wire -- As needed -- Electrical connections

Tools:

  1. Digital multimeter
  2. Soldering iron
  3. Solder wire
  4. Wire cutters
  5. Wire stripper
  6. Small screwdriver
  7. Optional oscilloscope

The 10µF electrolytic capacitors are a practical choice for this build. Their positive terminals should connect to ground because the input and output rails are negative relative to ground.

Prepare the Components

Start by checking the LM7905CT package and identifying its three terminals.

Inspect the capacitors and make sure their voltage ratings are suitable for the input and output voltages.

Prepare the perfboard, terminal blocks, and connecting wires.

Install the LM7905CT

Place the LM7905CT on the perfboard.

Leave enough space around the regulator for a heatsink if your application requires one.

Make sure the regulator terminals are not accidentally connected together by solder bridges.

Install the Input Capacitor

Connect a 10µF electrolytic capacitor between the negative input rail and common ground.

The capacitor's positive terminal goes to ground, while its negative terminal connects to the negative input rail.

Place the capacitor close to the regulator input.

Install the Output Capacitor

Connect the second 10µF electrolytic capacitor between the regulated output and ground.

Again, its positive terminal connects to ground and its negative terminal connects to the -5V output.

This capacitor helps improve the output response when the connected load changes.

Connect the Input and Output Terminals

Install two terminal blocks.

Clearly label the input terminals:

  1. VIN (-)
  2. GND

Label the output terminals:

  1. -5V OUT
  2. GND

Check every connection carefully before applying power.

Inspect the Circuit

Before powering the circuit, use a multimeter to check for accidental shorts between the input, output, and ground.

Pay particular attention to the polarity of the electrolytic capacitors and the regulator pin connections.

Testing and Verification

After assembly, the module should be tested before connecting it to any sensitive electronic equipment.

Test 1: No-load output measurement

  1. Connect a suitable negative DC power supply to the input.
  2. Set the input voltage to approximately -9V to -12V relative to ground.
  3. Turn on the supply.
  4. Set the multimeter to DC voltage.
  5. Measure the output between -5V OUT and GND.

The expected nominal output is -5V.

Test 2: Resistive load test

Connect a 100Ω, 1W resistor between the -5V output and ground.

The expected load current is approximately:

\[ I=\frac{5V}{100\Omega}=50mA \]

The resistor dissipates approximately 0.25W.

Measure the output voltage again and check whether it remains regulated.

Test 3: Temperature inspection

Allow the circuit to operate under load for several minutes.

Check the regulator temperature carefully. If the device becomes excessively hot, disconnect the supply and investigate the thermal design.

Do not assume that the regulator can deliver its full 1.5A rating without adequate cooling.

For example, with a -12V input and -5V output, a 500mA load would produce approximately:

\[ P=(12V-5V)\times0.5A=3.5W \]

This is substantial power dissipation and requires careful heatsink selection.

Actual performance should be recorded from your own measurements rather than assumed in advance.